Why TV Changes Channels By Itself?

Suppose you just come home after spending a whole busy day outside and now you just want to relax by watching your favorite show on your television and suddenly TV changes channels by itself. Yes, it might be so irritating to you.

But there is no doubt, a television occasionally changes channels without you prompting it to change the channel. Don’t be so hyper, you are not alone who is facing this issue for the first time. There are a lot of people who keep asking that their TV start to change channels by itself.

 The Channel automatically keeps changing channels on the DISH network which is so common issue among users who watch television over DISH.  Unfortunately, sometimes it becomes so difficult to find the reason for this problem.

But fortunately, if you find out the reason, you can fix this issue by yourself without taking the TV to the service center. So, in this article, we are going to discuss why your television is changing channels by itself and also figure out how to fix it.

Causes for your TV Keeps Changing Channel Automatically by itself

There can be some basic reasons for your TV channels keeps changing by themselves. The most common reasons are given below:

• Trespass of signals from the remote of your neighbor
• Stuck Button of your remote
• Carbon dust covered the controller board
• Software glitch

1. Trespass of Signals from the remote of your Neighbor

Signal interference of your neighbor’s remote is the most common reason for changing channels. However, if your neighbor is using the same model of remote control, then the censor of your TV might be pointed at their house, then it is normal to happen the issue of your TV keeps changing channels by itself.

Again, Ultra High-Frequency remotes will start to control the TV receiver from a long distance. So, this can be the possible reason for changing your channel, your neighbor has a UHF remote start to communicate with your receiver.

2. stuck Button of your remote control

The stuck button of the remote control or the TV board can be the other common reason for changing channels automatically. Sometimes it can happen that you stuck the next button of the remote or TV while pressing it, that’s why it is stuck, and then the TV starts to keep changing the channel itself.

3. Carbon Dust Covered the Controller Board

There must be dust on the controller board of your remote if you are using your television and remote for a long time. As we all know that dust contains carbon which allows the controller board to work automatically without pressing any button. So we must say, when carbon dust covered the controller board it can lead your TV to this issue. So it is also another possible reason behind the issue.

4. Software Glitch

This is also possible that Software glitches or faulty TV settings can be the main reason for this issue. So, these are the most common reasons TV changes channel by itself.

Yes, this is true, you cannot determine the exact reason for this issue but you can fix the issue by applying some troubleshooting ways that are given in this useful article.

How to fix the My Dish Change Channels by Itself Issue by yourself?

If you don’t know the exact reason triggering the automatic channel changing issue with your TV, then don’t worry, you can apply the given easy ways step by step to fix the issue.

1. Fix Stuck Buttons

If you notice that there is a stuck button on your remote and it is causing this issue. So in this way, you can easily remove the batteries from your remote, then it will stop changing channels automatically. After that, you need to Press and release the buttons repeatedly until the buttons no longer stick.

Now check if the problems have been resolved, if your TV still keeps changing channels by itself after removing batteries from the remote control, that means there must be something wrong with the TV buttons. In this way, you have to Click the TV button and check that no TV buttons are stuck. We hope so, it will solve the issue.

2. Fix Dusty Circuit Boards

If the dusty circuit board is the main reason then you can do that to fix the issue.

• First of all, you have to open the body case of your remote
• Now you have to remove the rubber button layer.
• Here, you can see a circuit board after removing that.
• Now you have to try cleaning it properly and gently using an alcohol-based cleaner with a soft cloth.
• Now you have set the board back to the remote again
• Next, you need to close the case and reconnect the batteries.
• If this will not work, then you have to press and hold the “Menu” button for a few seconds and wait until the reset process finishes.

Hopefully, this will resolve the issue.

Fix the Neighbor Remote Signal Interference

First of all, you have to turn the receiver towards another side and now see if the channels are automatically changing or not. If it stops changing the channel, that means, your neighbor is using the same model that communicates with your TV.

In this way, you have to place your TV in any other area, so that the signal is unable to interfere. If it doesn’t work, then it may be the UHF remote of your neighbor that making the issue. In this order, you need to disable the UHF setting on your TV, here is how to do this:

First of all, you have to remove the small antenna that is attached to the receiver. If it is not a removable antenna then you have to remove the ball from the end of the receiver. But, if your receiver doesn’t have any antenna then you have to disable the setting from UHF.

• First of all, go to Menu
• Then click on Preference
• Now click on Hardware Settings
• Next, you have to Disable UHF from there.

Configure Remote Control Address

If there is any software or faulty setting of your TV is the main culprit for changing channels by itself. Then you have to configure your remote-control address in the following way:

• First of all, go to Menu
• Next, click on Preferences
• Then click on Hardware Settings
• And hit the option of Remote Control Address.
• Next, you have to press and hold the option of “Enter”
• Now, press the “Mute” button until the mode button flashes.
• Then, you have to enter the receiver code and press the “Enter” button.
• Finally, you have to press the “Guide” button after seeing the flash of the “Mode” button.

Conclusion

So, in this useful post, we have explained the main reasons why TV changes channels by itself” and we have also mentioned the easy fixes. You just need to try them one by one to resolve the issue. So that’s all you need to know about that. We hope so, this article will help you a lot!